Adtran Total Access 908e manual

Adtran Total Access 908e
6.8 · 1
PDF manual
 · 2 pages
English
manualAdtran Total Access 908e
Quick Start Guide, 64240916L1-13B, November 2006 Copyright © 2006 ADTRAN, All Rights Reserved
For more detailed documentation, visit us online at www.adtran.com.

Quick Start Guide

®

Total Access 900e Series P/N 4240908L1, 4240916L1, 4240924L1, 4240924L2

GETTING STARTED

Two configuration methods are available for your Total Access 900e Series unit:
Web-based GUI
AOS Command Line Interface (CLI)
The GUI lets you configure the main unit settings and provides online guidance and
explanations for each setting. However, using the AOS CLI may be necessary for more
advanced configurations.

ACCESS THE GUI

You may access the web-based GUI from any web browser on your network by following these
steps:
1. Connect the unit to your PC using the ETH 0/1 port on the rear panel of the unit.
2. Set your PC to a fixed IP address of 10.10.10.2. If you cannot change the PC’s IP address,
you will need to change the unit’s IP address using the CLI. (Refer to the next two sections
for instructions.)
3. Enter the unit’s IP address in your browser address line. The default IP address is
10.10.10.1.
4. You will then be prompted for the username and password (the default settings are admin
and password).
5. The initial GUI screen appears.

ACCESS THE CLI

Access the AOS CLI via the CRAFT port or a Telnet session. To establish a connection to the
Total Access unit CRAFT port, you need the following items:
VT100 terminal or PC (with VT100 terminal emulation software)
Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate
interface for your terminal or PC communication port on the other end
1. Connect the DB-9 (male) connector of your serial cable to the CRAFT port on the rear
panel of the unit.
2. Connect the other end of the serial cable to the terminal or PC.
3. Insert the connector of the provided power cord into the power interface on the rear panel
of the unit, and plug the cord into a standard electrical outlet.
4. Once the unit is powered up, open a VT100 terminal session using the following settings:
9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the AOS
CLI.
5. Enter enable at the > prompt.Enter the enable password when prompted. The default
password is password.
CONFIGURE THE UNITS IP ADDRESS
The following steps create and IP address and subnet mask for the ETH 0/1. If you are not sure what IP
address to assign, please contact your network administrator.
1. At the # prompt, enter config terminal.
2. At the (config)# prompt, enter interface eth 0/1 to access the configuration parameters for the
ETH 0/1 Ethernet port located on the rear of the unit.
3. Enter ip address 10.26.12.12
255.255.255.0 to assign an IP address to the Ethernet port using a
24-bit subnet mask.
4. Enter no shutdown to activate the interface to pass data.
5. Enter exit to exit the interface commands and return to the Global configuration mode.
ENABLE TELNET ACCESS
The following steps create a password of adtran for Telnet access. By default, Telnet access is enabled
with a password of password.
1. Verify that the prompt of your unit displays (config)#.
2. Enter line telnet 0 4 to change the configuration parameters for the Telnet sessions.
3. Enter login to initiate Telnet access.
4. Enter password adtran
to change the login password for the Telnet sessions.
5. Enter exit to return to the Global Configuration mode.
6. Verify that the prompt of your unit displays (config)#.
7. Enter do write memory to save the current configuration.
The configuration parameters used in the examples outlined in this
document are for instructional purposes only. Please replace all
underlined entries (
example) with your specific parameters to configure
your application.
Depending on your configuration, you may need to set a default gateway as well
as using the (config)#ip default gateway command. If IP routing is enabled on
the unit, do NOT set a default gateway.

Manual

View the manual for the Adtran Total Access 908e here, for free. This manual comes under the category Not categorized and has been rated by 1 people with an average of a 6.8. This manual is available in the following languages: English. Do you have a question about the Adtran Total Access 908e or do you need help? Ask your question here

Need help?

Do you have a question about the Adtran Total Access 908e and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Adtran Total Access 908e owners to provide you with a good answer.

Number of questions: 0

Adtran Total Access 908e specifications

Below you will find the product specifications and the manual specifications of the Adtran Total Access 908e.

General
Brand Adtran
Model Total Access 908e | 4242908L1
Product Not categorized
EAN 6075650257160, 0607565025716
Language English
Filetype Usermanual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Adtran Total Access 908e below.

Is your question not listed? Ask your question here

No results