Adtran NetVanta 3200 manual

Adtran NetVanta 3200
7.5 · 1
PDF manual
 · 2 pages
English
manualAdtran NetVanta 3200
Quick Start Guide, 61202860L1-13B, July 2005 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright © 2005 ADTRAN, All Rights Reserved
For more detailed documentation, visit us online at www.adtran.com.

Quick Start Guide

®

NetVanta 3200 Router P/N 1202860L1

GETTING STARTED

Two configuration methods are available for your NetVanta router:
Web-based GUI
AOS Command Line Interface (CLI)
The GUI lets you configure the main unit settings and provides online guidance and explanations
for each setting. However, using the AOS CLI may be necessary for more advanced
configurations.

ACCESS THE GUI

You may access the web-based GUI from any web browser on your network by following these
steps:
1. Connect the router to your PC using the ETH 0/1 port on the back of the unit.
2. Set your PC to a fixed IP address of 10.10.10.2. If you cannot change the PC’s IP address,
you will need to change the unit’s IP address using the CLI. (Refer to the next two sections for
instructions.)
3. Enter the unit’s IP address in your browser address line. The default IP address is 10.10.10.1.
4. You will then be prompted for the username and password (the default settings are admin
and password).
5. The initial GUI screen appears.

ACCESS THE CLI

Access the AOS CLI via the CONSOLE port or a Telnet session. To establish a connection to the
NetVanta router CONSOLE port, you need the following items:
VT100 terminal or PC (with VT100 terminal emulation software)
Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate
interface for your terminal or PC communication port on the other end
1. Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the rear
panel of the unit.
2. Connect the other end of the serial cable to the terminal or PC.
3. Insert the connector of the provided power cord into the power interface on the rear panel of
the unit, and plug the cord into a standard electrical outlet.
4. Once the unit is powered up, open a VT100 terminal session using the following settings:
9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the
AOS CLI.
5. Enter enable at the > prompt.
6. Enter the enable password when prompted. The default password is password.
CONFIGURE THE UNITS IP ADDRESS
The following steps create an IP address and subnet mask for Ethernet port 0/1. If you are not
sure what IP address to assign, please contact your network administrator.
1. At the # prompt, enter config terminal.
2. At the (config)# prompt, enter interface eth 0/1 to access the configuration parameters for
the Ethernet port located on the rear of the unit.
3. Enter ip address 10.26.12.12
255.255.255.0 to assign an IP address to the Ethernet port
using a 24-bit subnet mask.
4. Enter no shutdown to activate the interface to pass data.
5. Enter exit to exit the Ethernet interface commands and return to the Global Configuration
mode.
The configuration parameters used in the examples outlined in this
document are for instructional purposes only. Please replace all
underlined entries (
example) with your specific parameters to configure
your application.
Depending on your configuration, you may need to set a default gateway
as well using the (config)#ip default gateway command. If IP routing is
enabled on the unit, do NOT set a default gateway.

Manual

View the manual for the Adtran NetVanta 3200 here, for free. This manual comes under the category Routers and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Adtran NetVanta 3200 or do you need help? Ask your question here

Need help?

Do you have a question about the Adtran NetVanta 3200 and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Adtran NetVanta 3200 owners to provide you with a good answer.

Number of questions: 0

Adtran NetVanta 3200 specifications

Below you will find the product specifications and the manual specifications of the Adtran NetVanta 3200.

General
Brand Adtran
Model NetVanta 3200
Product Router
EAN 0607565010590, 0607565011207
Language English
Filetype Usermanual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Adtran NetVanta 3200 below.

Is your question not listed? Ask your question here

No results