Adam T7V manual

Adam T7V
8.2 · 6
PDF manual
 · 22 pages
English
manualAdam T7V
14
T SERIES MANUAL [ENGLISH]

6. USING THE HF AND LF SWITCHES ON

THE REAR PANEL

On the rear panel for each T Series monitor, two 3-way switches labeled “LF” and “HF”
boost or cut the monitor’s respective high- and low-frequency responses by 2 dB. Each
switch also provides a neutral middle position, labeled “0,” that produces flat response
in their frequency range. If you’ve placed your T Series monitors optimally [see Section
2 of this manual], you’ll probably find that your T Series monitors sound the most
balanced
with both switches set to the “0” [flat] position.
A brief review of how room acoustics can affect loudspeaker performance will help you
get the most out of using your T Series monitors’ LF and HF switches:
Sound bouncing off bare walls and, typically to a lesser extent, the ceiling in your
control
room can create very short echoes that distort imaging and phase response
back at your mix position. Properly treating your room with acoustic foam or high-
density fiberglass sound panels reduces or prevents these problems by absorbing the
sound, rather than reflecting it back to your mix position. However, foam and fiberglass
sound panels absorb mostly high, midrange and—depending on the material used and
its thickness—upper-bass frequencies. [The thicker the material, the lower the extension
of frequencies that are absorbed, with high-density fiberglass absorbing frequencies
roughly a full octave lower than open-cell foam for the same thickness. For example,
both 2”-thick fiberglass wall panels and 4”-thick acoustic foam typically absorb sound
effectively down to around 250 Hz.] Because these materials absorb sound most effectively
in the treble range, a room heavily treated with acoustic foam or fiberglass sound
panels can make any loudspeaker’s playback of high frequencies sound muffled. To
re
store clarity and detail, your T Series monitors provide a HF switch setting that boosts
high-frequency response 2 dB.
Another acoustic phenomenon to keep in mind when placing your monitors in your
room is the boundary effect. The closer you place a loudspeaker to a room boundary
— a wall, floor or ceiling — the more bass frequencies will be acoustically boosted. To
preserve your T Series monitors’ flat frequency response, it’s important to nullify the
boundary effect by placing them at least 16 inches away from any wall. This is also
im
portant in order to prevent physical interference by the wall behind the monitors with
the cabinets’ rear-firing bass reflex ports. If ergonomics require you place your T Series
monitors close to a wall, setting the LF switch on the rear panel to the “-2 dB” setting
will cut the bass response an equal amount and help restore flat spectral balance.

Manual

View the manual for the Adam T7V here, for free. This manual comes under the category speakers and has been rated by 6 people with an average of a 8.2. This manual is available in the following languages: English. Do you have a question about the Adam T7V or do you need help? Ask your question here

Need help?

Do you have a question about the Adam and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

Adam T7V specifications

Below you will find the product specifications and the manual specifications of the Adam T7V.

The Adam T7V is a speaker that offers high-quality audio performance for various applications. With a tweeter and a woofer, this speaker ensures a balanced sound reproduction with detailed highs and deep bass. The woofer has a diameter of 7 inches, while the tweeter has a diameter of 1.9 inches. Equipped with line inputs, this speaker allows easy connection to external devices using RCA cables. It features a line-in balanced impedance of 10 Ω and a line-in unbalanced impedance of 20 Ω, providing flexibility in connectivity options. The RMS rated power of the Adam T7V is 70 W, delivering sufficient output for most audio needs. It is designed to minimize distortion, with a low total harmonic distortion (THD) of 0.5%. This ensures clear and accurate sound reproduction. With a noise level of 110 dB in high gain mode, the speaker maintains a high signal-to-noise ratio, resulting in a low level of background noise and enhanced audio clarity. The Adam T7V is constructed with quality materials to ensure reliability and durability over time. It is solidly built to withstand the demands of regular use and perform consistently. Overall, the Adam T7V is a versatile speaker suitable for a wide range of audio applications. It provides a balanced sound reproduction, easy connectivity options, and reliable performance. Whether used for music playback, multimedia production, or sound monitoring, this speaker offers a high level of audio quality and performance.

General
BrandAdam
ModelT7V | ADAM T7V
Productspeaker
LanguageEnglish
FiletypeUser manual (PDF)
Audio
Line-in Total Harmonic Distortion plus Noise (THD+N) (1kHz)- %
Line-out Total Harmonic Distortion plus Noise (THD+N) (1kHz)- %
Line-in Total Harmonic Distortion (THD)0.5 %
Frequency range39 - 25000 Hz
Noise level (high gain)110 dB
Line-in balanced impedance10 Ω
Line-in unbalanced impedance20 Ω
Loudspeakers
Built-in speaker(s)-
RMS rated power70 W
TweeterYes
WooferYes
Woofer diameter (imperial)7 "
Tweeter diameter (imperial)1.9 "
Display
Built-in display-
Ports & interfaces
Line inputs (RCA)1
XLR inYes
Design
Rack mounting-
Product colorBlack
Weight & dimensions
Width210 mm
Depth293 mm
Height347 mm
Weight7100 g
Packaging content
Cables includedAC
ManualYes
Power
Power consumption (max)132 W
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Adam T7V below.

When is my volume too loud?

A volume above 80 decibels can be harmful to hearing. When the volume exceeds 120 decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration.

Can bluetooth devices of different brands be connected to each other?

Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.

Wat is Dolby Atmos?

Dolby Atmos is a technology that ensures that the sound is reflected from the ceiling to where you are listening. This makes it possible to create a 5.1 effect with only 1 speaker.

What is bluetooth?

Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.

What is the weight of the Adam T7V?

The Adam T7V has a weight of 7100 g.

What is the height of the Adam T7V?

The Adam T7V has a height of 347 mm.

What is the width of the Adam T7V?

The Adam T7V has a width of 210 mm.

What is the depth of the Adam T7V?

The Adam T7V has a depth of 293 mm.

How do I connect my Adam T7V speaker to my audio source?

To connect your Adam T7V speaker to your audio source, utilize an XLR or RCA cable to connect the audio output of your source device to the corresponding input on the back of the speaker.

How can I adjust the volume of my Adam T7V speaker?

To adjust the volume of your Adam T7V speaker, simply turn the volume knob located on the front of the speaker to increase or decrease the sound level.

What is the optimal position for placing my Adam T7V speakers in a room?

For optimal sound performance, position your Adam T7V speakers at an equal distance from your listening position, forming an equilateral triangle. Additionally, ensure the speakers are placed on sturdy stands or surfaces to minimize vibrations.

How can I fine-tune the sound of my Adam T7V speakers?

The Adam T7V speakers offer adjustable high and low-frequency controls on the rear panel. Experiment with these controls to suit your listening preferences and room acoustics.

Can I connect my Adam T7V speakers to multiple audio devices simultaneously?

Yes, you can connect multiple audio devices to your Adam T7V speakers by using an external audio mixer or switcher. This allows you to conveniently switch between different sources without needing to re-cable each time.

Does the Adam T7V have a line-in Total Harmonic Distortion of 0.5%?

Yes, the Adam T7V has a line-in Total Harmonic Distortion of 0.5%. This means that the speaker delivers clear and accurate audio with minimal distortion.

Is the noise level (high gain) of the Adam T7V 110 dB?

Yes, the noise level (high gain) of the Adam T7V is 110 dB. This indicates that the speaker produces loud and immersive sound with minimal background noise.

Does the Adam T7V have a line-in balanced impedance of 10 Ω?

Yes, the Adam T7V has a line-in balanced impedance of 10 Ω. This allows for optimum compatibility with a wide range of audio devices, resulting in a balanced and reliable sound signal.

Does the Adam T7V have a tweeter and woofer?

Yes, the Adam T7V has both a tweeter and a woofer. This speaker is designed to deliver a full range of sound frequencies, with the tweeter handling the higher frequencies and the woofer producing the lower frequencies.

What is the RMS rated power of the Adam T7V?

The RMS rated power of the Adam T7V is 70 W. This power output allows the speaker to deliver high-quality sound and handle demanding audio playback, making it suitable for various listening environments and applications.

Is the manual of the Adam T7V available in English?

Yes, the manual of the Adam T7V is available in English .

Is your question not listed? Ask your question here

No results