ABB 7B500 manual

ABB 7B500
6.9 · 1
PDF manual
 · 8 pages
English
manualABB 7B500
2 MN905
SAFETY NOTICE Continued
Always use safety glasses with side shields (or full face shield) when operating grinder.
Do not use ordinary eyeglasses. Also use face or dust mask if cutting operation is dusty.
Do not overtighten wheel mounting screws. A damaged grinding wheel can disintegrate in all directions.
Overtightening wheel mounting screws can stress the grinding wheel and cause it to disintegrate during operation.
Wheel mounting screws should be tightened just enough to prevent grinding wheel from slipping on shaft when
grinding. Use only anges furnished with this grinder. The anges furnished with the grinder are designed to grip the
grinding wheel without introducing excessive stresses in the wheel.
Replace a cracked or chipped wheel immediately. A cracked wheel will disintegrate when operated, causing a
hazard to operator and nearby personnel. If a wheel has a chip or crack on any surface, do not use it.
Maintain 1/8 or less clearance between tool rest and wheel. This clearance is necessary to prevent the work
piece from becoming wedged between the wheel and tool rest and restricting nip areas in the machine.
Grind on rim face (side) of wheels only. Grinding on outside diameter of wheel weakens the wheel and may cause
wheel breakage.
Use wheels rated at or over 3600 RPM.

Table

Adjustable Lamp

Table

Water Tray

Water Pot

Water Tray

Rim Face

On−O − Reversing Switch

Installation When you receive your unit, there are several things you should do immediately.
1. Observe the condition of the shipping container and report any damage immediately to the commercial carrier
that delivered the product.
2. Verify that the part number you received is the same as the part number listed on your purchase order.
WARNING: When starting a grinder for the first time, or after installing a replacement grinding wheel, it is most important
that the operator stand aside for at least one minute of rotation at full speed. This is the correct practice
since grinding wheels can disintegrate if they have received damage during shipping or handling.
3. Mount grinder on solid bench. The grinder must be securely bolted to a rigid mounting surface. If a pedestal is
used, rst bolt pedestal securely to oor and then bolt grinder to pedestal.
4. Check grinder nameplate to make certain the rating is correct for the power source, voltage and frequency. See
electrical and grounding instructions for electrical service connection.
WARNING: Never install a wheel that is damaged, such as a chip or crack on any surface. A damaged wheel can
disintegrate while rotating at a high RPM or when work is placed against the wheel. This can severely harm
the operator or others in the area.
5. Inspect each Wheel
Carefully inspect the grinding wheels for damage. Never install a wheel that shows any sign of damage such as
a chip or crack on any surface. A damaged wheel can disintegrate while rotating at a high RPM or when work is
placed against the wheel. This can severely harm the operator or others in the area.
Note: Baldor catalog items #500 and #510 are supplied with mushroom head machine screws. Baldor catalog items
#522 and #532 Diamond wheel grinders are supplied with both types of hardware.
WARNING: Never install a wheel that is damaged, such as a chip or crack on any surface. A damaged wheel can
disintegrate while rotating at a high RPM or when work is placed against the wheel. This can severely harm
the operator or others in the area.
6. Install the Grinding Wheels (see Figure 1).
a. Plate Mounted Wheels
Remove the machine screws from the wheel ange. Attach the wheel to the wheel ange using
four 5/16-18 mushroom head machine screws.
b. Diamond Wheels
Remove the machine screws from the wheel ange. Attach the wheel to the wheel ange using
four 1/4-20 at head machine screws.

Manual

View the manual for the ABB 7B500 here, for free. This manual comes under the category grinders and has been rated by 1 people with an average of a 6.9. This manual is available in the following languages: English. Do you have a question about the ABB 7B500 or do you need help? Ask your question here

Need help?

Do you have a question about the ABB and is the answer not in the manual?

  • Receive updates on solutions
  • Get answers to your question

Question and answer

Number of questions: 0

ABB 7B500 specifications

Below you will find the product specifications and the manual specifications of the ABB 7B500.

General
BrandABB
Model7B500 | 7B500
Productgrinder
EAN0781568127339
LanguageEnglish
FiletypeUser manual (PDF)
Other features
TypeDry/wet grinder
Weight & dimensions
Weight49486 g
Package weight49486 g
Height431.8 mm
Width469.9 mm
Depth698.5 mm
Features
Product colorBlue
Performance
Number of grinding wheels2
Grinding wheel diameter152 mm
Grinding wheel thickness25.4 mm
Grinding wheel bore31.75 mm
Idle speed (max)3600 RPM
Power
Cable length2.4 m
AC input frequency60 Hz
AC input voltage115 V
Amperage5 A
show more

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the ABB 7B500 below.

What is the weight of the ABB 7B500?

The ABB 7B500 has a weight of 49486 g.

What is the height of the ABB 7B500?

The ABB 7B500 has a height of 431.8 mm.

What is the width of the ABB 7B500?

The ABB 7B500 has a width of 469.9 mm.

What is the depth of the ABB 7B500?

The ABB 7B500 has a depth of 698.5 mm.

Is the manual of the ABB 7B500 available in English?

Yes, the manual of the ABB 7B500 is available in English .

Is your question not listed? Ask your question here

No results