Name: 7inova 7W310
Brand: 7inova
SKU: 103991
Rating: 53 (1 reviews)

manual7inova 7W310

1) Restore the 7W310’s configuration to its factory default settings.

(With 7W310 powered on, use a pin to press and hold the Reset

button for about 3-5 seconds before releasing it).

2) To log in the Web Management page, use the default user name and

password: admin, admin. To connect to the Wireless Network, use

the default password on the label.

3) Try to configure 7W310 once again by following the instructions in

the previous steps of the QIG.

What can I do if I forgot my password?

Appendix: Troubleshooting

3.3.3 Select wireless which you want to connect and enter the password (if

wireless don’t have password is “None”)

3.3.4 Then click “Apply” and wait for 3~5 seconds it is complete.

5.2 Wireless Security Configuration

4 Reconnect to Repeater

4.1 Click “Start→Control Panel→Network and Internet→Network and Sharing

Center→Change adapter settings→Wi-Fi(right click)→Properties”

5 Configuring via Web Browser

5.1 Wireless Base Configuration

4.2 Double click “Internet Protocol Version 4(TCP/IPv4)”

4.3 Select “Obtain an IP address automatically” and “Obtain DSN

server address automatically”. Click “OK”. Back to the last

interface and click “OK”

4.4 Select the wireless network name configured in “3 Configuration Mode” ,

click “Connect” button.

4.5 If you encrypted wireless network in “3 Configuration Mode”, the following

message will be displayed on web browser, fill in password, click “OK”

Please click “Advanced Mode → Wireless Settings → Wireless Basic

Settings” located at the web management interface, the following

message will be displayed on your web browser:

You could configure the minimum number of Wireless settings for

communication, such as SSID and Channel. The Access Point can be set

simply with only the minimum setting items.

Please click “Advanced Mode → Wireless Settings → Wireless Security

Settings” located at the web management interface, the following message

will be displayed on your web browser:

Setup the wireless security and encryption to prevent from unauthorized

access and monitoring. Supports 64/128-bit WEP, WPA-Personal, WPA2-

Personal encryption methods

5.3 Change Management password

Default password of Wireless Repeater is “admin”, and it’s displayed on

the login prompt when accessed from web browser. There’s a security risk

you don’t change the default password, since everyone can see it. This is

very important when you have wireless function enabled.

To change password, please follow the following instruction:

Please click “Advanced Mode → System Tools → User Password Change”

menu on the web management interface, the following message will be

displayed on your web browser:

5.4 Firmware Upgrade

The system software used by this repeater is called as “firmware”, just like

any applications on your computer, when you replace the old application

with a new one, your computer will be equipped with new function. You

can also use this firmware upgrade function to add new functions to your

repeater, even fix the bugs of this repeater.

Please click “Advanced Mode → System Tools → System Upgrade”

located at the located at the web management interface, then the

following message will be displayed on your web browser.

5.5 Settings Backup and Restore, Factory Default

You can backup all Setting of this repeater to a file, so you can make

several copied of repeater configuration for security reason.

To backup or restore repeater setting, please follow the following instruction:

Please click “Advanced Mode → System Tools → Backup and Recovery”

and “Advanced Mode → System Tools → Restore Factory Settings”

located at the web management interface, then the following message will

be displayed on your web browser:

If you want to keep original password unchanged, click “Cancel”.

Click “Save” button, the WiFi Repeater will become effective

Click “Apply” button, the WiFi Repeater will become effective.

Click “Browse” button first, you’ll be prompted to provide the filename of

firmware upgrade file. Please download the latest firmware file from our

website, and use it to upgrade your repeater.

After a firmware upgrade file is selected, click “Upgrade” button, and the

repeater will start firmware upgrade procedure automatically.

The procedure may take several minutes, please be patient.

Wireless Mode

Channel

SSID Broadcast

Supports 11b/g/n mixed modes

Wireless Signal On/Off

6(default)

Wireless Status

SSID

Wireless On/Off

Main Service Set Identifier.

It’s the “name” of your wireless network.

Back up

Browse

Restore All Settings

Press ”Back up” button, you can please save it as another

filename for different versions, and keep it in a safe place.

Press ”Browse” to pick a previously-saved configuration file

from your computer, and the click “Save”. After the replaced

by the file you just uploaded.

Click “Restore All Settings” button to remove all settings

Note: Never interrupt the upgrade procedure by closing the web browser or physically

disconnect your computer from repeater. If the firmware you upgrade is corrupt, the

firmware upgrade will fail, and you may have to return this repeater to the dealer of

purchase to ask for help. (Warranty voids if you interrupted the upgrade procedure).

Click “Save” and “Restore All Settings” button. The repeater will restart.

09 Wireless-N Repeater08 Wireless-N Repeater 10 Wireless-N Repeater 11 Wireless-N Repeater

13 Wireless-N Repeater12 Wireless-N Repeater 14 Wireless-N Repeater 15 Wireless-N Repeater

300Mbps Wireless Repeater

FW RVE: 7R152_V1.0

Browse

Click “Apply” button, the WiFi Repeater will become effective.

View the manual for the 7inova 7W310 here, for free. This manual comes under the category Wifi repeaters and has been rated by 1 people with an average of a 5.3. This manual is available in the following languages: English. Do you have a question about the 7inova 7W310 or do you need help? Ask your question here

Need help?

Do you have a question about the 7inova and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other 7inova owners to provide you with a good answer.

marco • 7-5-2021No comments

can i have a firmware update for wifi extender w310x

Answer this question

Antonio Tapia • 30-5-2020No comments

Como reseteo la contraseña?

Answer this question

Number of questions: 2