7inova 7W211 manual

7inova 7W211
7.5 · 2
PDF manual
 · 2 pages
English
manual7inova 7W211
1) Restore the 7W211’s configuration to its factory default settings.
(With 7W211 powered on, use a pin to press and hold the Reset
button for about 3-5 seconds before releasing it).
2) To log in the Web Management page, use the default user name and
password: admin, admin. To connect to the Wireless Network, use
the default password on the label.
3) Try to configure 7W211 once again by following the instructions in
the previous steps of the QIG.

What can I do if I forgot my password?

Appendix: Troubleshooting

3.3.3 Select wireless which you want to connect and enter the password (if
wireless don’t have password is “None”)
3.3.4 Then click “Apply” and wait for 3~5 seconds it is complete.
5.2 Wireless Security Configuration

4 Reconnect to Repeater

4.1 Click “StartControl Panel→Network and InternetNetwork and Sharing
CenterChange adapter settingsWi-Fi(right click)→Properties

5 Configuring via Web Browser

5.1 Wireless Base Configuration
4.2 Double click “Internet Protocol Version 4(TCP/IPv4)
4.3 Select Obtain an IP address automaticallyand Obtain DSN
server address automatically. Click OK. Back to the last
interface and click OK
4.4 Select the wireless network name configured in “3 Configuration Mode” ,
click “Connect” button.
4.5 If you encrypted wireless network in3 Configuration Mode, the following
message will be displayed on web browser, fill in password, click OK
Please click “Advanced Mode → Wireless Settings → Wireless Basic
Settings” located at the web management interface, the following
message will be displayed on your web browser:
You could configure the minimum number of Wireless settings for
communication, such as SSID and Channel. The Access Point can be set
simply with only the minimum setting items.
Please click Advanced ModeWireless Settings Wireless Security
Settingslocated at the web management interface, the following message
will be displayed on your web browser:
Setup the wireless security and encryption to prevent from unauthorized
access and monitoring. Supports 64/128-bit WEP, WPA-Personal, WPA2-
Personal encryption methods
5.3 Change Management password
Default password of Wireless Repeater is “admin”, and it’s displayed on
the login prompt when accessed from web browser. There’s a security risk
you don’t change the default password, since everyone can see it. This is
very important when you have wireless function enabled.
To change password, please follow the following instruction:
Please click Advanced Mode System Tools User Password Change
menu on the web management interface, the following message will be
displayed on your web browser:
5.4 Firmware Upgrade
The system software used by t
his repeater is called as firmware, just like
any applications on your computer, when you replace the old application
with a new one, your computer will be equipped with new function. You
can also use this firmware upgrade function to add new functions to your
repeater, even fix the bugs of this repeater.
Please click “Advanced Mode → System Tools → System Upgrade
located at the located at the web management interface, then the
following message will be displayed on your web browser.
5.5 Settings Backup and Restore, Factory Default
You can backup all Setting of this repeater to a file, so you can make
several copied of repeater configuration for security reason.
To backup or restore repeater setting, please follow the following instruction:
Please click “Advanced ModeSystem Tools Backup and Recovery
and “Advanced Mode → System Tools → Restore Factory Settings
located at the web management interface, then the following message will
be displayed on your web browser:
If you want to keep original password unchanged, click “Cancel”.
Click “Save” button, the WiFi Repeater will become effective
Click “Apply” button, the WiFi Repeater will become effective.
Click “Browse” button first, you’ll be prompted to provide the filename of
firmware upgrade file. Please download the latest firmware file from our
website, and use it to upgrade your repeater.
After a firmware upgrade file is selected, click “Upgrade” button, and the
repeater will start firmware upgrade procedure automatically.
The procedure may take several minutes, please be patient.
Wireless Mode
Channel
SSID Broadcast
Supports 11b/g/n mixed modes
Wireless Signal On/Off
6(default)
Wireless Status
SSID
Wireless On/Off
Main Service Set Identifier.
It’s the “name” of your wireless network.
Back up
Browse
Restore All Settings
Press ”Back up” button, you can please save it as another
filename for different versions, and keep it in a safe place.
Press ”Browse” to pick a previously-saved configuration file
from your computer, and the click “Save”. After the replaced
by the file you just uploaded.
Click “Restore All Settings” button to remove all settings
Note: Never interrupt the upgrade procedure by closing the web browser or physically
disconnect your computer from repeater. If the firmware you upgrade is corrupt, the
firmware upgrade will fail, and you may have to return this repeater to the dealer of
purchase to ask for help. (Warranty voids if you interrupted the upgrade procedure).
Click “Save” and “Restore All Settings” button. The repeater will restart.
09 Wireless-N Repeater08 Wireless-N Repeater 10 Wireless-N Repeater 11 Wireless-N Repeater
13 Wireless-N Repeater12 Wireless-N Repeater 14 Wireless-N Repeater 15 Wireless-N Repeater
300Mbps Wireless Repeater
FW RVE: 7R152_V1.0
Click “Apply” button, the WiFi Repeater will become effective.

Manual

View the manual for the 7inova 7W211 here, for free. This manual comes under the category Wifi repeaters and has been rated by 2 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the 7inova 7W211 or do you need help? Ask your question here

Need help?

Do you have a question about the 7inova 7W211 and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other 7inova 7W211 owners to provide you with a good answer.

Patrick van Grieken • 13-1-2016 No comments

How do I download this ??? Prefer PDF

Answer this question
Bernard Valentin • 17-3-2015 No comments

I would like to know if this device supports MAC filtering when configured in AP mode. Thank you.

Answer this question
Gerard contant • 9-7-2014 No comments

Ik zoek de nederlandstalige handleiding

Answer this question
Mike Hamel • 2-7-2014 No comments

I am having trouble getting my ipad to connect to this device. I am a novice when it comes to setting up this type of thing. Any help is appreciated.

Answer this question
Antonio • 4-1-2015 No comments

Qualcuno ha configurato 7inova 7w211? Io ho seguito con religiosa attenzione le istruzioni ed il video su YouTube ma non sono mai riuscito ad arrivare alla mascherina dove digitare admin

Answer this question

Number of questions: 5

7inova 7W211 specifications

Below you will find the product specifications and the manual specifications of the 7inova 7W211.

General
Brand 7inova
Model 7W211
Product Wifi repeater
Language English
Filetype Usermanual (PDF)

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the 7inova 7W211 below.

Is your question not listed? Ask your question here

No results